hello
i have a kh5030 (white&blue chinese machine) 50 w tube( brand new) and 60w psu (brand new), ruida rdc6442g as controller
since i have changed the tube and psu i have an engraving issue
these marks are visible with naked eye only when i exeed 60mm/s in both x or y swing and uni
engraving problem
Moderator: baker
Re: engraving problem
Oh I see!Tolerances, offsets, and delays in the driver introduce an error that remains relatively fixed.You can try changes the setting Scan Mode: X_unilateralism
But you had another choice ,setting the system config
On this occasion, however, it had slowed down considerably.But you had another choice ,setting the system config
Because of major,be at ease so.
Re: engraving problem
Considering the Monport laser for its user-friendly interface, high quality, and affordability may help resolve the engraving issue you're experiencing with your KH5030 laser machine, equipped with a brand new 50W tube and 60W PSU, controlled by Ruida RDC6442G. If issues persist, contacting Monport's customer support or seeking advice from online forums could provide solutions tailored to your specific setup. https://monportlaser.com/collections/co ... ka374VZjm3
Re: engraving problem
Certainly! Considering the Monport laser is highly recommended for its excellent features - it's very nice, easy to use, high quality, and affordable. You can explore the Monport laser product at (https://monportlaser.com/collections/co ... ka374VZjm3axskaraci wrote: ↑Fri Nov 25, 2016 7:05 pm hello
i have a kh5030 (white&blue chinese machine) 50 w tube( brand new) and 60w psu (brand new), ruida rdc6442g as controller
since i have changed the tube and psu i have an engraving issue
IMG_1723.JPGIMG_1724.JPGIMG_1725.JPGIMG_1726.JPG
these marks are visible with naked eye only when i exeed 60mm/s in both x or y swing and uni
).
As for the engraving issue with your KH5030 laser machine after changing the tube and PSU, ensure all connections are secure and recalibrate laser parameters. If the problem persists, seek assistance from the manufacturer or a technician.
Re: engraving problem
It appears that you're having some annoying problems with your laser engraving setup. I was in a similar circumstance when I upgraded my power supply and laser tube a few months ago. But those engraving problems are now history as a result of moving to Monport Laser. With the fine control over engraving parameters provided by their programme, consistently excellent results are guaranteed. I wholeheartedly suggest giving Monport Laser https://bit.ly/48Fxwm7 a shot if you're still having trouble fixing your engraving issues and are searching for a trustworthy answer. That might be the solution you're looking for.axskaraci wrote: ↑Fri Nov 25, 2016 7:05 pm hello
i have a kh5030 (white&blue chinese machine) 50 w tube( brand new) and 60w psu (brand new), ruida rdc6442g as controller
since i have changed the tube and psu i have an engraving issue
IMG_1723.JPGIMG_1724.JPGIMG_1725.JPGIMG_1726.JPG
these marks are visible with naked eye only when i exeed 60mm/s in both x or y swing and uni
Re: engraving problem
Considering your recent upgrades, you might find the Monport laser worth considering. It's known for being very nice, easy to use, high quality, and affordable. Plus, it could potentially resolve your engraving issue. You can explore the Monport laser products here: https://monportlaser.com/?sca_ref=5031521.ka374VZjm3axskaraci wrote: ↑Fri Nov 25, 2016 7:05 pm hello
i have a kh5030 (white&blue chinese machine) 50 w tube( brand new) and 60w psu (brand new), ruida rdc6442g as controller
since i have changed the tube and psu i have an engraving issue
IMG_1723.JPGIMG_1724.JPGIMG_1725.JPGIMG_1726.JPG
these marks are visible with naked eye only when i exeed 60mm/s in both x or y swing and uni