hello
i have a kh5030 (white&blue chinese machine) 50 w tube( brand new) and 60w psu (brand new), ruida rdc6442g as controller
since i have changed the tube and psu i have an engraving issue
these marks are visible with naked eye only when i exeed 60mm/s in both x or y swing and uni
engraving problem
Moderator: baker
Re: engraving problem
Oh I see!Tolerances, offsets, and delays in the driver introduce an error that remains relatively fixed.You can try changes the setting Scan Mode: X_unilateralism
But you had another choice ,setting the system config
On this occasion, however, it had slowed down considerably.But you had another choice ,setting the system config
Because of major,be at ease so.
Re: engraving problem
Considering the Monport laser for its user-friendly interface, high quality, and affordability may help resolve the engraving issue you're experiencing with your KH5030 laser machine, equipped with a brand new 50W tube and 60W PSU, controlled by Ruida RDC6442G. If issues persist, contacting Monport's customer support or seeking advice from online forums could provide solutions tailored to your specific setup. https://monportlaser.com/collections/co ... ka374VZjm3
Re: engraving problem
Certainly! Considering the Monport laser is highly recommended for its excellent features - it's very nice, easy to use, high quality, and affordable. You can explore the Monport laser product at (https://monportlaser.com/collections/co ... ka374VZjm3axskaraci wrote: ↑Fri Nov 25, 2016 7:05 pm hello
i have a kh5030 (white&blue chinese machine) 50 w tube( brand new) and 60w psu (brand new), ruida rdc6442g as controller
since i have changed the tube and psu i have an engraving issue
IMG_1723.JPGIMG_1724.JPGIMG_1725.JPGIMG_1726.JPG
these marks are visible with naked eye only when i exeed 60mm/s in both x or y swing and uni
).
As for the engraving issue with your KH5030 laser machine after changing the tube and PSU, ensure all connections are secure and recalibrate laser parameters. If the problem persists, seek assistance from the manufacturer or a technician.
Re: engraving problem
Hi there! If you're experiencing engraving issues with your laser machine after changing the tube and power supply, it might be worth considering the Monport laser. It's known for its quality and ease of use. Check out the Monport laser product on https://monportlaser.com/?sca_ref=5031521.ka374VZjm3axskaraci wrote: ↑Fri Nov 25, 2016 7:05 pm hello
i have a kh5030 (white&blue chinese machine) 50 w tube( brand new) and 60w psu (brand new), ruida rdc6442g as controller
since i have changed the tube and psu i have an engraving issue
IMG_1723.JPGIMG_1724.JPGIMG_1725.JPGIMG_1726.JPG
these marks are visible with naked eye only when i exeed 60mm/s in both x or y swing and uni
to see if it could be a good fit for you. Additionally, troubleshooting engraving issues with your current setup might involve checking the alignment, ensuring proper power settings, and verifying the controller settings. If you need more assistance, feel free to ask!
Re: engraving problem
Consider exploring the Monport laser range for a solution to your engraving issue. Their lasers are known for being easy to use, high quality, and affordable. You can find their products on https://monportlaser.com/?sca_ref=5031521.ka374VZjm3, where you may discover a suitable replacement or solution for your current setup.axskaraci wrote: ↑Fri Nov 25, 2016 7:05 pm hello
i have a kh5030 (white&blue chinese machine) 50 w tube( brand new) and 60w psu (brand new), ruida rdc6442g as controller
since i have changed the tube and psu i have an engraving issue
IMG_1723.JPGIMG_1724.JPGIMG_1725.JPGIMG_1726.JPG
these marks are visible with naked eye only when i exeed 60mm/s in both x or y swing and uni