Can someone tell me why the part that I'm engraving into is off center by 1/8".
Please the attached photo.
The X is whats off
For some reason the photo rotated.
Thanks
Steven
Nova 35 100 Watt
RDW V8.01.18
Not Engraving in the absolute position
Moderators: baker, Thunder laser - Tom, Thunder Laser -Nolan
Forum rules
All members should make themselves familiar with the forum rules. Please ensure you read this section of the forum BEFORE posting.
This sub-forum is only for thunderlaser users ask for tech support from thunderlaser tech persons directly. The normal member should raise your questions in the General Discussion sub-forum. Before ask a new question, please read the "Previously Asked Questions"first to save your time.
All members should make themselves familiar with the forum rules. Please ensure you read this section of the forum BEFORE posting.
This sub-forum is only for thunderlaser users ask for tech support from thunderlaser tech persons directly. The normal member should raise your questions in the General Discussion sub-forum. Before ask a new question, please read the "Previously Asked Questions"first to save your time.
- stevenresnick
- Posts: 25
- Joined: Fri Jun 17, 2016 8:25 am
Not Engraving in the absolute position
- Attachments
-
- IMG_0168.jpg (167.12 KiB) Viewed 22632 times
Re: Not Engraving in the absolute position
Hi Steven,
It seems that controller is not working well.
Maybe the memory of controller is full,please clean up the files.
Or you can just format the memory as following.
On LCD panel>>File>>Other+>>format the memory speedily.
After that,let me know if that problem is resolved or not.
It seems that controller is not working well.
Maybe the memory of controller is full,please clean up the files.
Or you can just format the memory as following.
On LCD panel>>File>>Other+>>format the memory speedily.
After that,let me know if that problem is resolved or not.
- stevenresnick
- Posts: 25
- Joined: Fri Jun 17, 2016 8:25 am
Re: Not Engraving in the absolute position
Hi Ben,
Thanks for the res response.
How do I clear the memory of the controller??
What happens when I format the controller?
Will i have to enter any info or settings?
I a wait your response before I make any changes
Thanks
Steven
Thanks for the res response.
How do I clear the memory of the controller??
What happens when I format the controller?
Will i have to enter any info or settings?
I a wait your response before I make any changes
Thanks
Steven
- stevenresnick
- Posts: 25
- Joined: Fri Jun 17, 2016 8:25 am
Re: Not Engraving in the absolute position
Hi Ben,
I went a head and tried what you suggested and it didn't change at all.
Please advise what you think I should do next.
Thanks
Steven
I went a head and tried what you suggested and it didn't change at all.
Please advise what you think I should do next.
Thanks
Steven
- stevenresnick
- Posts: 25
- Joined: Fri Jun 17, 2016 8:25 am
Re: Not Engraving in the absolute position
Ben,
I just tried another test......
When I have a shape (square) and place it in an absolute position it cuts it out exactly where I placed it, but if I put another square inside of it to engrave it doesn't line up. Like in the original photo.
Thanks,
Steven
I just tried another test......
When I have a shape (square) and place it in an absolute position it cuts it out exactly where I placed it, but if I put another square inside of it to engrave it doesn't line up. Like in the original photo.
Thanks,
Steven
Re: Not Engraving in the absolute position
Hi Steven,
As you said,it's more likely about the controller or software issue.
Please send me the test files for checking.Thanks.
As you said,it's more likely about the controller or software issue.
Please send me the test files for checking.Thanks.